Lockable Shaft Nuts with Axial Clamping

ALMA shaft nuts with axial clamping offer easy access where radial space is limited, uniform three-point clamping and precise locking with relatively low actuation force.

On these shaft nuts, the clamping screws are arranged axially and accessible from the end face. This makes them particularly suitable for installations where space around the outer diameter is limited and the clamping screws cannot be operated radially. Sufficient axial access for assembly tools and a torque wrench is required.

ALMA shaft nuts with axial clamping feature a three-point clamping system. The three evenly spaced clamping elements promote symmetrical force application and favourable load distribution within the nut body. According to the manufacturer, this achieves 30 per cent greater clamping force than a comparable two-point clamping system.

Compression springs are integrated between the clamping elements and the clamping ring. These exert only a small opposing force, allowing particularly sensitive control of the clamping action. The design, described by the manufacturer as patented, allows the previously adjusted position of the shaft nut to be locked precisely and in a controlled manner.

According to the manufacturer and the underlying comparative tests, the ALMA clamping principle requires only approximately one third of the clamping force that may be needed with other clamping methods to lock the shaft nut in position. The exact reduction in force depends on the size, thread, material pairing and system used for comparison.

The low locking force required reduces the risk of the previously adjusted position shifting during clamping. It also minimises local deformation or twisting of the nut body. This supports high axial runout accuracy and repeatable adjustment, particularly in precision bearing arrangements, spindles and other demanding mechanical engineering applications.

ANS

Precise, secure, compact. Radial three-point clamping

ANS-LH

Precise, secure, compact. Version with a left-hand thread

ANS-A2

Precise, secure, compact. Vacuum version in grade 1.4305 stainless steel

ANSB

Compact, precise, robust. Radial three-point clamping

ANSK

Reliable locking in minimal installation space. Radial two-point clamping

WAK

Reliable locking for demanding applications. Axial locking

Lockable Shaft Nuts with Radial Clamping

ALMA shaft nuts with radial clamping combine high clamping force and structural rigidity with high axial runout accuracy, reduced machining requirements and reliable, releasable locking.

ALMA shaft nuts with three-point clamping feature three clamping points evenly spaced around the circumference. This design ensures more uniform force distribution and, according to the manufacturer, achieves 30 per cent greater clamping force than a comparable two-point clamping design. It also promotes favourable load distribution within the nut body.

The relatively large radial cross-section gives the nut body high structural rigidity. This reduces unwanted deformation during tightening and clamping, supporting reliable and repeatable positioning on the shaft.

Extra-wide versions are available for applications with increased axial loads. The larger load-bearing cross-section enables them to withstand and transmit higher axial forces. The permissible load must be determined based on the specific size, shaft thread and manufacturer’s specifications.

The internal thread and the bearing-side end face of the shaft nut are machined in a single setup, ensuring high axial runout accuracy. This is particularly beneficial for precision bearing arrangements, spindles and rotating assemblies, as the axial force is distributed as evenly as possible across the adjoining component.

Die Wellenmutter wird über radial angeordnete Klemmschrauben beziehungsweise Sicherungsstifte direkt auf dem Wellengewinde fixiert. Ein zusätzliches Sicherungsblech ist daher nicht erforderlich. Bei den entsprechenden Ausführungen werden die Sicherungsstifte gemeinsam mit dem Innengewinde der Mutter gefertigt. Dadurch greifen sie präzise in das Wellengewinde ein, ohne den eingestellten Planschlag wesentlich zu beeinflussen.

Since no lock washer is required, there is also no need for a corresponding groove in the shaft thread. This eliminates time-consuming milling and subsequent deburring of the locking groove. It also reduces the number of components required, simplifying design, procurement, assembly and subsequent maintenance.

The shaft nut is first moved to the desired axial position or tightened to the specified torque. It is then locked radially using the integrated clamping screws. As the locking action is achieved through a separate clamping operation, the nut can also be used as a precision adjusting nut. Positioning and locking against rotation can therefore be set largely independently of each other.

Do you have any questions?

Get in touch. Your contact for all enquiries about lockable shaft nuts:

Daniela Münkel

anfrage@alma-driving.de

Phone: +49 9394 9700 34